Change or rekey · Kawartha Lakes
Lock Replacement & Upgrade
Three teenagers, a dog walker, a cleaner and one house key that keeps going missing.
In plain words
Sometimes the reason is simply that the hardware looks wrong or has weathered badly. Road salt, freeze-thaw and humid summers are hard on finishes, and a brass handleset can go blotchy while a lacquered knob peels. The locksmith helps you pick a finish that suits the exposure, whether matte black, satin nickel or a PVD brass that resists tarnish, and matches the deadbolt, handleset and interior levers so the entrance reads as one design. Function and grade are chosen alongside looks, so a door refreshed for appearance also comes out better protected.
How the visit goesThe century home's original mortise lock takes a key the size of a spoon, sticks in humid weather and has worn its strike to a groove. You want a lock that works every day without giving up the old door.
Lock Replacement & Upgrade
How the visit goes
Measuring the existing preparation
Before any product is chosen the door is measured. Backset first, the distance from the door edge to the centre of the bore, which on most doors here is 60 or 70 millimetres. Then the cross-bore diameter, the edge-bore size, the shape of the latch faceplate, the door thickness and the handing. The strike cut-out and any glass, trim or storm door that limits where hardware can sit are noted too. These few numbers decide which locks will drop straight into the door and which would need a filler plate, an extension kit or fresh drilling, so they are written down before the catalogue is opened.
Fitting the latch or bolt to the door
Most modern latches and bolts adjust between the two common backsets, so the unit is set to the measured figure and slid into the edge bore. A spring latch goes in with its bevel facing the strike, while a deadbolt is oriented the way its markings or instructions call for, not by that bevel rule. The faceplate should sit flush in its mortise; where the old cut-out differs in shape or size, the mortise is trimmed with a sharp chisel, or a round drive-in collar is used where the door was prepared that way. The bolt is checked to travel freely before anything else goes on, since a bolt that binds in the door will bind under the key too.
An opening that is stronger, not just newer
Where the strike was reinforced, the improvement is mostly invisible and worth understanding. Long screws now tie the strike through the jamb into the framing, the pocket has been cut to take the whole bolt, and any split wood has been repaired. Together these make the frame the equal of the deadbolt, which is the part most break-ins defeat. The locksmith points out what changed so you can check it yourself: a bolt that seats fully with the door closed and a strike that stays put under a firm push. A twice-yearly look at those screws keeps it that way.
Lock Replacement & Upgrade
In the van
Adjustable latch or bolt
Handleset with matching deadbolt
Graded deadbolt
Knob or lever entry set
Reinforced strike plate and strike box
Lock Replacement & Upgrade
What affects the quote
Smart lock setup
Fitting a keypad or smart deadbolt includes programming codes, pairing to a phone or hub and calibrating the bolt, which is time on top of the mechanical installation and is named in the quote.
Type of lock
A knob set, a lever, a deadbolt, a full handleset with deadbolt above, a patio door lock and a keypad or smart deadbolt each carry a different hardware cost and take different time to fit.
Condition of the old hardware
Hardware that comes off cleanly is one thing; painted-over trim, seized or stripped screws and a cylinder that has to be drilled out add time before the new lock can go on.
What to have ready
- Can you photograph each lock from outside, inside and along the door edge?
- Is there glass in or beside the door?
- Which doors are you thinking about, and what is on each one now?
Lock Replacement & Upgrade: questions
QuestionsIs it possible to upgrade just the exterior locks now and handle interior doors later?
Yes, and it is a common way to spread the work out. Exterior doors carry the security load, so starting there with a graded deadbolt and a reinforced strike covers the part that matters most first. Interior locks, passage sets, privacy locks on bathrooms and bedrooms, can be scheduled for a later visit without affecting anything already done, and the locksmith can note what was fitted so the second visit matches it.
My deadbolt only locks if I push the door. Will a new lock cure that?
The push is a sign the bolt and the strike pocket are out of line, which is a door and frame matter more than a lock fault. A new deadbolt is welcome if the old one is worn, but the visit also adjusts the strike, deepens the pocket or tightens hinges so the bolt throws freely with the door simply closed. Done together, the door locks with a fingertip and the new hardware works as designed.
Can you replace the lock on a sliding patio door or French doors?
Yes. Sliding doors take a replacement mortise hook lock sized to the rail, often with a keyed exterior, and benefit from a secondary foot bolt or a pin through the frames. French doors are secured by treating the inactive leaf properly with flush bolts into the head and sill, then fitting a deadbolt to the active leaf with a strike into that reinforced edge. Both are routine parts of a residential upgrade.
Related services
- Deadbolt InstallationThe back door has a deadbolt in name only: a short bolt, a thin brass strike held by two little screws, and a jamb you can flex with your palm.
- Vintage Mortise Lock ServiceYou bought a house with its original hardware and a bag of loose keys.
- Smart Lock InstallationYour mother still lives on her own, and the personal support worker, the pharmacy delivery and two siblings all need to get in on different days.